circuit analysis techniques multisim

Employing qualified writers in writing service like is a fundamental step in ensuring that the work produced is of high quality. This not only benefits the students who use these services but also contributes to the credibility and reputation of the company in the academic community. One of the primary reasons for employing qualified writers in academic writing services is their in-depth knowledge of the field. These writers typically hold advanced degrees in related disciplines, making them well-versed in the subject matter. Their expertise allows them to produce accurate, relevant, and insightful content that aligns with the academic standards. Qualified writers enable students to better manage their time. By outsourcing some of your academic writing tasks to, you can allocate more time to other important aspects of you education, such as practice, internships, and studying for exams. This balanced approach contributes to a holistic learning experience.

Circuit Analysis

Circuit Analysis Techniques in Multisim

This week’s lab is based on the application of circuit analysis techniques to a resistive circuit in Multisim. You will learn to utilize Multisim to perform the mesh analysis.

  1. Work Exercise 48 from Chapter 4 to determine the current i1’ and power supplied by 1V source.
  2. Redo the problem, this time without the dependent current source 5i1.
  3. Fill in the calculated values in the table below:

Calculated current ‘i1’

Save your time - order a paper!

Get your paper written from scratch within the tight deadline. Our service is a reliable solution to all your troubles. Place an order on any task and we will take care of it. You won’t have to worry about the quality and deadlines

Order Paper Now

Calculated Power supplied by 1V

Measured Current ‘i1’

Measured Power supplied by 1V

With Dependent Source (5i1)


Without Dependent Source (5i1)

  1. Construct Figure 4.73 from Chapter 4 in Multisim.
    1. Run the simulation to measure the current ‘i1’ and power supplied by 1V source record the measurements in the table. (Use 5% tolerances for each of the resistors)
    2. Next, remove the dependent source ‘5i1’ from the circuit and run the simulation again to record the measurements in the table. (Use 5% tolerances for each of the resistors)
    3. Take the screen capture for the measurements of current and power supplied and dissipated by each resistor and complete the table above.
  2. Answer the following questions:
    1. Are the measured values same as calculated values? If not, explain why they are different?
    2. Is the supplied power distributed among all the components in the circuit? Show that total power supplied is equal to the sum of powers dissipated in each component.
    3. What was the effect of removing the dependent source from the circuit? Does the overall power supplied or power dissipated change?
  3. Create a new word document called “Lab2_StudentID.docx” with your GID substituted into the file name.
  4. Save the analysis from step 1 & 2 and simulation results from step 4 along with the table and screen captures of all the measurements. Make sure to answer the questions in step 5.
  5. Upload file “Lab2_StudentID”.

Grading Rubrics

Demonstrate understanding of Kirchhoff’s and Watts laws

10 points

Analyze the circuit in Exercise 48 to calculate Current and Power

25 points

Circuit design in Multisim (Figure 4.73)

10 points

Measurement of Current and Power in Multisim (With dependent source)

10 points

Measurement of Current and Power in Multisim (Without dependent source)

10 points

Use of resistor tolerances

5 points

Answer to the questions

20 points

Lab Report (includes table, measurement with proper units, screenshots, APA guidelines)

10 points


100 points qualified writers are well-acquainted with the intricacies of academic writing. They are proficient in following the formatting, citation, and referencing guidelines specified by different institutions. This ensures that the work produced is not only academically sound but also meets the expectations of professors and professionals. Academic assignments often require critical analysis and evidence-based writing. qualified writers possess the skills to critically evaluate research, synthesize information, and present arguments backed by credible sources. This level of rigor is essential where evidence-based practice is paramount. When students receive well-researched and well-written assignments, they have the opportunity to learn from these examples. high-quality work serves as a valuable reference point for students, helping them understand complex concepts, research methodologies, and effective writing techniques.

Do you need a similar assignment done for you from scratch? We have qualified writers to help you. We assure you an A+ quality paper that is free from plagiarism. Order now for an Amazing Discount!
Use Discount Code "Newclient" for a 15% Discount!

NB: We do not resell papers. Upon ordering, we do an original paper exclusively for you.